ابزارهای تحقیق و توسعه, پروگرامرها
پروگرامر Altera USB BLASTER – پروگرامر FPGA
وضعیت برای خرید:
در انبار موجود نمی باشد
- Stably support SignalTap II embedded logic analyzer function, no mistake while crawling data.
- Fully support all Altera products such as CPLD: MAX3000, MAX7000, MAX9000 and MAXII.
- FPGA: Stratix, StratixII, StratxIII, Cyclone, CycloneII, CycloneIII, ACEX1K, APEX20K and FLEX10K etc.
- Active serial configuration device: EPCS1, EPCS4, EPCS16, EPCS64 etc.
- Enhanced configuration devices: EPC1, EPC4.
- Supports 3 download mode: AS, PS and JTAG.
۱,۵۳۰,۰۰۰ریال ۱,۹۹۱,۰۰۰ریال
در انبار موجود نمی باشد
مقایسهمحصولات مشابه
- آردوینو - Arduino, ابزارهای تحقیق و توسعه, بردهای تحقیق و توسعه, سیم و کابل, کابل USB, کابل آردوینو, لوازم جانبی آردوینو
کابل USB پرینتری طول 30 سانتی متر
آردوینو - Arduino, ابزارهای تحقیق و توسعه, بردهای تحقیق و توسعه, سیم و کابل, کابل USB, کابل آردوینو, لوازم جانبی آردوینوکابل USB پرینتری طول 30 سانتی متر
0 out of 5(0)- کابل USB 2.0
- کابل USB A نری به USB B نری (کابل پرینتر)
- برای اتصال دستگاههای دارای کانکتور USB Type B Female مادگی به کامپیوتر
- انتهای اول: کانکتور USB نوع A نری (USB Type A Male Connector)
- انتهای دوم : کانکتور USB نوع B نری (USB Type B Male Connector)
- طول کابل: 30 سانتی متر (30 cm)
- نوع کابل: کابل USB Type B (یو اس بی تایپ B)
- رنگ: آبی شفاف
- جنس غلاف بیرونی کابل: PVC
- کابل شیلددار
- ساز گار با استانداردهای USB 2.0، USB 1.1 و USB 1.0
- برای اتصال برد آردوینو UNO به کامپیوتر
- برای اتصال برد آردوینو مگا به کامپیوتر
- USB AM/BM Cable (USB 2.0 Type A Male to Type B Male)
- USB 2.0 Data Transfer Cable
- USB Type-A male connector fits standard PC, USB hub and similar ports
- USB Type-B male connector fits devices that use this connector, like printers, scanners and similar devices
- Allows you to connect like Arduino UNO, Arduino Mega 2560 USB port to the computer.
- 24 AWG power, 28 AWG signal conductors
- Cable is fully shielded
- Color: Transparent Blue
- Cable Length: 1 foot (30 cm)
- Meets USB 2.0 specification
- Backwards compatible with USB 1.0 and USB 1.1 Signals
- Hot-swappable cable
- Plug and Play
SKU: 9130100136 - ابزارهای تحقیق و توسعه, بردهای AVR, بردهای آردوینو, بردهای تحقیق و توسعه
برد آردوینو نانو CH340 – Arduino NANO CH340
ابزارهای تحقیق و توسعه, بردهای AVR, بردهای آردوینو, بردهای تحقیق و توسعهبرد آردوینو نانو CH340 – Arduino NANO CH340
0 out of 5(0)- نام برد: برد آردوینو نانو CH340 – Arduino Nano CH340
- میکروکنترلر: ATmega328P
- فرکانس کاری میکروکنترلر: 16 MHz
- ولتاژ کاری میکروکنترلر: 5 ولت
- محدوده تغذیه برد (محدوده توصیه شده): 7 ولت تا 12 ولت
- محدوده تغذیه برد (محدوده حداکثری): 6 ولت تا 20 ولت
- حافظه فلش (Flash Memory): 32 کیلوبایت (2 کیلوبایت از آن برای Bootloader استفاده شده است)
- حافظه EEPROM: 1 کیلوبایت
- حافظه SRAM: 2 کیلوبایت
- تعداد پایههای دیجیتال: 14
- پایههای آنالوگ: 8
- پایههای PWM: 6
- تراشه ارتباطی: CH340G
- نوع کانکتور USB: Mini USB Connector
- Microcontroller: ATmega328
- Operating Voltage (logic level): 5 V
- Input Voltage (recommended): 7-12 V
- Input Voltage (limits): 6-20 V
- Digital I/O Pins: 14 (of which 6 provide PWM output)
- Analogue Input Pins: 8
- DC Current per I/O Pin: 40 mA
- Flash Memory: 32 KB of which 2 KB used by bootloader
- SRAM: 2 KB
- EEPROM: 1 KB
- Clock Speed: 16 MHz
- Automatic reset during program download
- Power OK blue LED on the bottom
- Green (TX), red (RX) and orange (L) LED
- +5V to AREF jumper
- Auto sensing/switching power input
- Small mini-B USB for programming and serial monitor (cable not included)
- ICSP header for direct program download
- Power OK blue LED on the bottom
- Standard 0.1” spacing DIP (breadboard friendly)
- Manual reset switch
SKU: 5020100005 - ابزارهای تحقیق و توسعه, پروگرامرها
پروگرامر CH341A برای تراشه های EEPROM و FLash
0 out of 5(0)- USB interface
- With CH341A chip
- Support 24 EEPROM and 25 SPI flash 8pin or 16pin chip
- With 24/25 status indicator lamp
- Support USB to TTL conversionSupport 24EEPROM and 25 SPI flash 8pin/ 16pin chip
- Recognize 25 series chip automatically
- Supports download STC series procedure of single chip
- SPI pin to support expanding the utility
- STC microcontroller supports a full range of program download
- Support expanding the utility by SPI pin
- With SOP8 SOP16 to DIP8 converter board
SKU: 5050100114 - ابزارهای تحقیق و توسعه, بردهای AVR, بردهای آردوینو, بردهای تحقیق و توسعه
برد آردوینو پرو مینی 3.3 ولت – Arduino Pro Mini 3.3V
ابزارهای تحقیق و توسعه, بردهای AVR, بردهای آردوینو, بردهای تحقیق و توسعهبرد آردوینو پرو مینی 3.3 ولت – Arduino Pro Mini 3.3V
0 out of 5(0)- نام برد: برد آردوینو پرو مینی مدل 3.3V (Arduino Pro Mini 3.3V)
- تراشه ATmega328P با فرکانس کاری 8 مگا هرتز
- خانواده میکروکنترلر: میکروکنترلر 8 بیتی AVR از سری ATmega.
- فرکانس کاری تراشه میکروکنترلر: 8 مگاهرتز (8 MHz)
- بدون مبدل USB به سریال
- پشتیبانی از ریست خودکار
- حداکثر 150mA جریان خروجی
- محدوده تغذیه ورودی بین 3.3V تا 12V
- دارای ولتاژ رگولاتور روی برد با خروجی 3.3V
- دارای LED وضعیت
- درای LED تغذیه
- 1 x Arduino Pro Mini 3.3V 8Mhz ATMEGA328P
- 3 x Male Header connector.
- Microcontroller: ATmega328 running at 8MHz with external resonator (0.5% tolerance)
- Clock Frequency: 8MHz.
- Flash Memory: 32KB of which 2 KB used by bootloader *
- SRAM: 2 KB
- EEPROM: 1 KB
- USB connection off board
- Support Serial Download
- Supports auto-reset
- 3.3V regulator On Board
- Max 150mA output
- Over current protected
- Reverse polarity protected
- Support external 3.3V-12V DC power supply
- Board Power Supply: 3.3 -12 V
- Supports 9V battery power supply
- On board Power and Status LEDs
- 14 Digital input/Output Port Rx, TX, D2~D13,
- 8 Analog input Ports A0~A7
- 6 PWM ports, D3, D5, D6, D9, D10, D11
- One Pair TTL level serial port RX/TX
- UART: 1
- SPI: 1
- I2C: 1
- Analog Input Pins: 8
- External Interrupts: 2
- DC Current per I/O Pin: 40 mA
- Dimension: 33.3*18.0mm
- Low-voltage board needs no interfacing circuitry to popular 3.3V devices and modules (GPS, accelerometers, sensors, etc)
SKU: 5020100009



















تا این لحظه نظری در مورد این محصول ارسال نشده است.